您要查找的是不是:
- Install the high pressure relief valve in the compressor manifold fitting. 在压缩机歧管配件里安装高压释放阀。
- Install a 125 PSI pressure relief valve in the cold water supply line. 在冷水供应管道上安装一个125psi的减压安全阀。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必须正确安装,使得降温减压安全阀和排水管道都能够完全排泄。
- Temperature and Pressure Relief Valve is required, but may not be factory installed. 需要降温减压安全阀,但可能不在工厂安装。
- Note: The installation of a separate pressure relief valve is necessary for installations using gas shutoffs. 注意:采用燃气关闭阀,有必要安装独立的压力安全阀。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通过这种功能,det系列将系统压力保持在温度压力安全阀的排放设置下。
- It can simplify the fire supply system of highrise building by applying pressure relief valve to vertical compartment. 采用减压阀对高层建筑物的消防给水系统进行竖向分区 ,可以简化系统。
- An ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. 正如以前所提到,每个锅炉都应该安装一个ASME第四节认证的压力安全阀。
- Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure. 每个热水供暖锅炉都必须配置压力安全阀,其设置的泄压压力必须小于锅炉的最大工作压力。
- DO NOT tamper with the electronic control board, temperature sensors, heating elements, electrical connections, or temperature and pressure relief valve. 不要篡改电气控制板,温度感应器,加热元件,电气连接,或降温减压安全阀。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正确安装降温减压安全阀,并配置排泄管引导至一个敞开的排水口,并确保不会被冻结。
- Temperature and pressure relief valve properly installed with a discharge line run to an open drain and protected from freezing. 正确安装降温减压安全阀,并配置排泄管引导至一个敞开的排水口,并确保不会被冻结。
- NOTE: 15" diameter chambers are standardly furnished with a pressure relief valve, factory set at 60psi to protect the chamber from excessive pressure. 注:在压力安全阀上,15英寸直径的腔室室标准配置,工厂设置是60psi,以保护腔室不会出现压力过大现象。
- Periodic discharge of the temperature and pressure relief valve may be due to thermal expansion in a closed water supply system. 在一个封闭的水供应系统中,热膨胀可能导致降温减压安全阀的周期性排泄。
- In order to prevent misuse, and some special pressure relief valve and the special connection between the cylinder mouth. 为了防止误用,有些专用减压阀与钢瓶之间采用特殊连接口。
- A water heater's temperature and pressure relief valve must be piped to the nearest drain in order to avoid damage in the event the valve is actuated. 热水器的降温减压安全阀必须用管道连接到最近的排水口,以避免万一阀门启动所造成的破坏。
- Temperature and pressure relief valve -factory provided aSME rated relief valve protects against excessive temperature and/or pressure buildup within the tank. 过热和超压安全阀---厂家在本款热水器上配置通过aSME(美国机械工程师协会)认证的安全阀,当内胆容器内出现温度过高或累积压力过大等异常情况时,进行降温和减压,提供可靠的安全保护。
- Install auxiliary (bleeder) pressure relief valve downstream of the reducing valve, in any convenient location where slight spillage is not objectionable. 在减压阀的下游安装辅助的(泄放)压力安全阀,可以安装在任何能够能够忍受轻微溢出的位置上。
- It was pressure relief valve in order that cooling or yes decompression that the instant twain parameter overproof,control turn automatism on water injection valve or. 当两参数超标时,控制器将自动打开喷水阀或者是卸压阀以便降温或者是降压。
- Building valves - Combined temperature and pressure relief valves - Tests and requirements. 建筑阀门。温度和压力组合安全阀。试验和要求。