您要查找的是不是：
- pivot pin lock pin 枢销锁销
- Place a pivot pin into the pivot point. 把大头针扎在旋转点上。
- steering knuckle king pin locking pin 转向关节主销键钉,转向节主销键钉
- Place a pivot pin into the bp. Mark the curved line A-bp.onto the pivot paper. 在胸点上孔一枚大头针。在旋转纸上画出A到胸点的弧线。
- Place a pivot pin into the BP. Mark the curved line A-BP onto the pivot paper. 在胸点上孔一枚大头针。在旋转纸上画出A到胸点的弧线。
- Lay the front bodice on a clean sheet of paper and place a pivot pin into the bust point. 把前身样板放在一张透明纸上并把大头针孔在胸点处。
- Pivot pins are constructed of stainless steel. 枢轴销采用不锈钢结构。
- Thoroughly clean and liberally grease pivot pin and lightly tap in a straight line without pausing. 彻底清洁枢轴并到处涂上润滑油后沿直线不停轻拍。
- If the aperture is set to "P" or "A", turn the aperture ding while pressing the "P" or "A" lock pin. 如果光圈要调到“P”或 “A”,请按住“P”或 “A”锁定拴同时转动光圈环。
- This paper analyzes and compares the ordinary heat treatment technology of Q275 steel knuckle pivot pin with the quenching and backfiring technology. 摘要分析、比较了Q275钢钩尾销普通热处理工艺与锻热淬火＋回火工艺。
- Keeps a good balance thanks to the equal interval fluting of lock pin and hook spanner. 由于锁紧销和扳手槽的等距分布,平衡性好。
- Therefore, it is suggested that knuckle pivot pin should be heat treated by the adoption of the quenching technology of heat forging and backfiring. 故提出对钩尾销采用锻热淬火+回火的热处理工艺。
- Results Follow-up showed none happened to fracture disunion or malunion and none occurred to postoperative infection or bending of lock pin. 结果随访本组病例,无一例出现骨折不愈合及畸形愈合,无术后感染及锁钉折断弯曲。
- Drop tight seating is accomplished over the full pressure range because a slight clearance at the pivot pin assures complete seating between the disc ring and body ring. 由于在枢轴销上的空隙很小,所以在整个压力范围内都可以实现漏斗形紧密阀座密封,确保阀瓣环和阀体环之间的阀座密封的完整性。
- Flip top fiberglass enclosures standardly furnished with locking pin to lock the lid in the open position. 顶部翻转玻璃纤维外壳,标准配置锁销,将盖锁在开口位置。
- This construction avoids the need for extending the pivot pins through the valve body. 这种结构消除了将枢轴销伸长穿出阀体的必要性。
- The seat, disc and pivot pins are combined into one subassembly secured to the inlet side of the body with a locking ring in sizes 3" and smaller. 阀座，阀瓣和枢轴销构成一个分总成，采用尺寸3英寸或更小的锁环固定在阀体进口一侧。
- A locking pin inserted in the end of a shaft, as in an axle, to prevent a wheel from slipping off. 车辖，制轮装在辕底部，如车轴上用来预防车轮滑动锁栓
- He chiseled a hole in the door to fit a new lock. 他在门上凿了个孔，以便装一把新锁。
- This lock can only be opened from the inside. 这把锁只能从里面打开。
