您要查找的是不是：
- normal tolerance distribution 正态耐性分布
- The diagnosis principle and diagnosability conditions are proposed, and the normal tolerance network test nede voltage interval are given by interval iterative algorithm. 该方法给出了容差情况下诊断的原理和可诊断性条件，并利用区间迭代算法，给出了容差网络无故障情况下的测试节点电压范围。
- The Normal tolerances are in accordance with ISO 492:2002. 普通级公差符合2002年的ISO 492标准。
- Brick combination schemes shall be prepared before bricklaying as per pre-laying of bricks and tolerance distribution of refractory bricks and bricks shall be manufactured accordingly. 砌筑前应根据预砌的情况与耐火砖公差分布情况，编制搭配使用上砖方案，并进行相应的加工。
- SKF thrust ball bearings are made to Normal tolerances as standard. SKF推力球轴承以普通级公差为标准。
- Cones and cups having a width tolerance that differs from the Normal tolerance are identified by a designation suffix according to table 2 where the actual tolerance values are provided. 宽度公差同普通级公差不同的内锥体和外锥环圈根据表2以型号后缀表示,实际公差数值见表。
- rectangular tolerance distribution 矩形耐性分布
- SKF cam rollers are produced to Normal tolerances as standard, except for the tolerance of the crowned runner surface diameter which is twice the Normal tolerance. 标准的SKF凸轮滚子按照标准公差生产,但是球形滚轮表面直径的公差则是标准公差的两倍。
- Wilson-Worcester tolerance distribution 威-武二氏耐性分布
- The paper draw the fuzzy mathematical principle into the tolerance distributing of the assemble dimensional chain, and presented the concept of fuzzy reliability of this chain. 将模糊数学原理引入到装配尺寸链公差分配中,提出了装配尺寸链装配模糊可靠度的概念。
- Bearings up to and including 300 mm bore diameter are produced to higher precision than the ISO Normal tolerances. 孔径达(含)300mm的轴承的制造,使用比ISO正常公差更高的精确度。
- SKF four-point contact ball bearings are produced as standard to Normal tolerances. 标准生产的SKF四点接触球轴承符合普通级公差。
- SKF indexing roller units are produced to Normal tolerances corresponding to ISO 492:1994. SKF分度滚子单元为标准公差,与ISO 492:1994标准相符。
- SKF spherical roller thrust bearings are produced as standard to Normal tolerances as specified in ISO 199:1997. 标准的SKF球面滚子推力轴承是按照ISO 199:1997规定的标准公差制造的。
- The bore diameter and width of the IR inner rings are made to Normal tolerances in accordance with ISO 492:2002. 根据2002年的ISO 492标准,IR内圈的孔径和宽度以普通级公差制造。
- The diameter tolerances for these bearings deviate from the Normal tolerances for the other rolling bearings, see section "Tolerances". 这些轴承的公差值偏离其他滚动轴承的普通公差,参见"公差"一节。
- The tolerances for CL7C specification bearings correspond to Normal tolerances except for the running accuracy which has been tightened considerably. CL7C规格轴承公差相当于普通级公差,除了运行精度比普通级公差严格很多。
- If you combine the three products and give the recommended dosage, your child will be within the normal tolerable range of vitamin C intake. 如果您结合三种产品，并给予推荐的剂量，您的孩子的维生素C的摄入量是在正常承受范围内的。
- SKF single row cylindrical roller bearings are manufactured to Normal tolerances for dimensional accuracy and to P6 tolerances for running accuracy as standard. 标准制造的SKF单列圆柱滚子轴承以普通级公差的尺寸精度生产,运行精度为P6公差。
- Inch bearings are manufactured to Normal tolerances, according to standard BS 292: Part 2:1982 and with Normal radial internal clearance, which conforms to ISO 5753:1991. 英制轴承的常规公差符合英国标准BS 292:Part2:1982,并带符合ISO 5753:1991标准的常规径向内部游隙。
