您要查找的是不是:
- coupler knuckle pin hole 钩耳孔
- coupler knuckle pin 钩舌销,车钩关节销
- A discussion on the NDT of inner wall of pin - hole on coupler knuckle 货车钩舌销孔内壁无损检测方法探讨
- There is a pin hole between outside shell and output axis. 外套与输出轴的径向有一个插销孔。
- The stress of E-grade steel coupler knuckle was analyzed and the expression of stress intensity factor of the cracks on the coupler knuckle wrist area was given. 摘要对重载列车E级钢钩舌进行了应力分析,导出了钩腕面裂纹的应力强度因子表达式。
- One such crack formed on the net section at the pin hole, much like an eyebar failure. 形成在销钉孔净截面处的一条裂纹非常象眼杆破坏。
- Drilling method of pin hole: the pin hole shall be predrilled by supplier prior to hot dip galvanization. 销钉孔的钻法:销钉孔应为供应商在热镀锌预钻好。
- Flux Corrosion is typified by pin hole leaks, generally in the bottom of a horizontal line. 典型例子是由于针孔泄漏导致的焊剂侵蚀,通常发生在水平管道的底部。
- The paper analyses the necessity for piston in modern auto to adopt noncircular pin hole. 简述了采用活塞异形销孔的必要性及其结构特点。
- The Si-Mn steel track plate and pin usually exist the early abrasion, one of the main reasons is the burr defect of pin hole. 硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。
- The causes to the core hole cracking in the coupler knuckle castings and the remedies 钩舌铸造泥孔开裂原因及措施
- The Si-Mn steel track plate and pin usually exist the early abrasion,one of the main reasons is the burr defect of pin hole. 硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。
- By homogenous design and Seger's glaze theory,a high-grade sanitary pocerlain glaze has been obtained,which possess a glossy and no pin hole surface. 利用均匀设计法和塞格尔釉式理论,研制出一种釉面光泽度高且无针孔的高档卫生陶瓷釉料。
- No. 13 couplers often occur failures such as coupler body and yoke cracks, coupler knuckle fracture etc. during operation.These seriously affect normal operation of the railway vehicles. 摘要13号车钩在运用过程中经常出现钩体裂纹、钩尾框裂纹和钩舌折断等故障,严重影响列车的正常运行。
- Of course after a while the novelty of it is gone - tame to take a rangefinder, a pin hole camera, or whatever I never did. 但是最终这意味着我不得不花费更多的时间和精力去拍我的相片。它强迫我在构图时以一种新鲜的视觉去看,去试验相机的摆放位置。
- High strength bolts for steel structure, bolts for diggers, hex bolts with split pin hole, bolts for automobile cylinder cap and non-standard components. 高强度钢结构螺栓,挖掘机螺栓,六角头绞制孔螺栓,汽车缸盖螺栓及非标准件。
- A new machining principle for non-cylinder pin hole of piston was presented by using giant magnetostrictive material (GMM) to control the deformation of tool rod. 摘要利用超磁致伸缩材料的特性控制刀杆弯曲变形,提出了一种加工活塞异形销孔的新方法。
- The NC boring lathe equipped with this kind of deformable arm can bore special shaped pin hole for piston efficiently, and meanwhile meet the demand of micro meter accuracy. 装有这种新型变形镗杆的NC镗床能高效地镗削活塞异形销孔,并达到微米精度的要求。
- Quenching plus high-temperature tempering of Type 13 coupler knuckle 13号车钩钩舌销的调质处理
- Heat Treatment Process Improvement of Steering Knuckle Pin 转向节主销热处理工艺改进