您要查找的是不是：
- back pressure return water 余压回水
- pressure return water 压力回水
- What is maximum acceptable back pressure? 如果是,给出可接受的最大背压?
- If the VSI's needle shows a descent (rotates downward), apply a little back pressure on the joystick to return the airplane to level flight. 如果VSI 的针显示下降(转动得向下), 施加一点反压力在控制杆退回飞机到平实飞行。
- Seating load and tightness is dependent on back pressure. 阀座密封负载和紧密性与反压力相关。
- This back pressure is no problem for the rupture disk. 如果压力放散系统的压力进入到爆破片中，对爆破片不会产生影响。
- Several different types of valves are in use. Some are back pressure valves. 有几种不同的阀在使用中,有些是反向压力阀。
- The configuration of supply and return water main and riser in the pipe well of the system is analyzed. 结合实例,分析了系统中管井内供回水干管、管的布置。
- Points out problems in setting expansion joints for supply and return water risers. 摘要指出了在供回水立管中间设置伸缩节存在的问题。
- Diplegs play an important role as pressure seals against the considerable back pressure generated. 料腿则起着对产生的相当大的背压加压密封作用。
- The most important complication of urinary tract obstruction is renal parenchymal atrophy as a result of back pressure. 尿路梗阻最重要的并发症为反压所致的肾实质萎缩。
- In-house: For managing cost, many products return water there is glaze in the turn, or a pad that used difference of stretch small, sealed function. 内部：为了节约成本，不少产品返水弯里没有釉面、或使用了弹性小、密封性能差的封垫。
- The abuses existing in the original turbid return water disposal system, the necessity and the reformation by adapting [M+F] method were introduced. 分析了柳钢中板厂原有浊环水处理系统中存在的弊端和进行改造的必要性以及应用[M+F]净化处理方法进行的改造。
- Back Pressure Propagation of network congestion information upstream through an internetwork. 网际中上传的网络拥塞信息。
- This filter is designed to have very little back pressure and is easy to squeeze with a faster flow rate. 这是为了过滤很少背压,易于挤压得更快流量。
- To whatever extent is practical, several orifices/traces shall be supplied from a local steam manifold and shall discharge to local return water / condensate manifold. 孔板/伴热管应尽量从本地蒸汽集合管开始，并尽可能排入本地回水/冷凝液集合管。
- The big and small rubber plugs has locking mechanism to prevent back pressure and has good drillability. 大小胶塞设有锁紧机构，注完水泥后可防止回压，且附件具有良好的可钻性；
- The reason a steady state was never reached was that the back pressure built up too slowly. 不能达到稳定状态的理由是背部压力上升太慢。
- The spray penetration decreases and overall SMD increases with the increasing back pressure. 随著背压的升高，油束贯穿度减小而整体索特平均直径增加。
- The pressure returns essentially to that in the incident blast wave which decays with time. 压力大体上回复到随着时间逐渐衰减的入射爆震波的压力。
