您要查找的是不是：
- Repair welding of air inlet pipe in high pressure cylinder 高压缸进汽插管焊接修复
- DISCUSSION ON AIR LEAKAGE PROBLEM OF AIR INLET PIPE IN DIESEL ENGINE 柴油机进气管漏气问题的探讨
- secondary air inlet pipe 二次空气入口管
- air inlet pipe 进气管
- Floor clearance to the inlet pipe. 进水管口至进水池底的高度。
- RAM AIR INLET MECHANICAL LINKAGE. 冲压空气进口机械连杆机构。
- Remove the air inlet hose from the throttle body and air cleaner. 从节流阀体和空气滤清器上拆下气流入口软管。
- Turn off supply pressure and observe float drop to open air inlet. 关闭供应压力,观察浮子下降,因此开启空气进口。
- Check found birdstrike on radome and R engine air inlet. 雷达罩和右发进气道口有鸟击痕迹。
- Air inlet throttle valve with pneumatic actuator and positioner. 空气进气节流调节阀：带有气动定位和执行机构。
- Connect the air inlet hose to the throttle body and the air cleaner. 将空气入口软管接至节流阀体和空气滤清器。
- The inlet pressure sensor is fixed to a inlet pipe directly with a boltand prevent gas leak through two seals. 进气压力传感器是用一个螺栓直接固定到进气管上，并通过两个密封圈来防止漏气。
- The exhaust ducting is cooled by four air inlets around the jet pipe. 排气管道被四个围绕喷射管道的进口空气冷却。
- In case the condensation water level lowered,auxiliary valve falls and steam enter the kibble through inlet pipe,key valve be closed. 当集水池的凝结水水位下降时，封闭进汽管的副阀落下，蒸汽从进汽管进入阀腔的吊桶，吊桶上浮使排水口的主阀紧紧关闭。
- Slowly open vent needle valve just as air inlet opens. Record differential pressure. 当空气进口开启时,慢慢开启排气针形阀。记录压差。
- Slowly open needle valve "C" bypass (yellow) just as air inlet opens. Record differential pressure. 正当空气进口打开时，慢慢开启针形阀“C”旁路（黄）。记录压差。
- Separation of the water supply from the air inlet is accomplished by means of a diaphragm seal. 供水与空气的隔离是通过采用隔膜密封的方法实现的。
- Next, let's make the simple panel under the air inlet that we can find on the side. 接下来，让我们作一个简单小组根据空气进说，我们能够找到对的一面。
- Separation of the water supply from the air inlet is accomplished by means of a diaphragm seal . 水供应与空气进口的分离通过隔膜密封的方法实现。
- According to the insufficiency of the essential spots such as the up - axis of digestion autoclave easy to break, the damages of the heating tube, the heating tube swilled over by the inlet pipe etc. 针对拜尔法生产氧化铝的溶出机组压煮器上部轴容易断裂、加热管束破损、进料管冲刷加热管束等关键部位存在的不足,简要介绍从1995投产以来所进行的一些有益的改进,对提高以加热压煮器为主的溶出机组的设备运转率有很大的帮助。
