该词条未找到_海词词典

您要查找的是不是：

upper cylinder bore wear 上止点附近的气缸壁磨损
lower cylinder bore wear 下止点附近气缸壁的磨损
Trim the upper cylinder with the extrusion and delete the extruded shape. 用拉升体修剪圆柱体,然后删除拉升体。
Every powder produces erosion or bore wear to some extent. 每一种无烟药都会有某种程度的烧蚀或炮膛磨损。
The honed crosshatch pattern in the cylinder bore acts like a file to allow the rings to wear.The rings quickly wear down the "peaks" of this roughness, regardless of how hard the engine is run. 被珩磨成刀路相互交叉的油缸内孔像一把锉刀去摩擦密封环，密封环很快就将各高点磨掉，这与狠用发动机没有关系。
The circle should extend slightly above the centerline of the upper cylinder to make sure the inner radius of the blend does not drop below the cylinder radius. 圆应该拉升到略高于圆柱体的中心线,确保混合的内半径不会低于圆柱体的半径。
Reciprocating pumps convert rotary motion to linear motion. Pump speed in rpm determines the pumps output volume for any given combination of cylinder bore and piston stroke. 循环泵将曲轴旋转运动转化为柱塞的直线运动。泵速转每分钟决定了任何气缸和活塞组合的排泵量。
In diesel engine industry, the development of small cylinder bore and several cylinder bores diesel engine and spare parts is supported. 内燃机行业，支持发展小缸径、多缸径柴油机及零部件。
Hot load and mechanical load coupling make piston to produce crackle, piston-ring glued and scuffing of cylinder bore and so on. 热负荷和机械负荷耦合将导致活塞产生裂纹、活塞环胶结以及拉缸等。
The different functions and cutting thicknesses in the boring process of hydraulic cylinder bore with four cutting tools fitted on one spindle are presen ted. 一根刀杆上四种切削刀具在液压缸内孔加工过程中的不同功能及不同切削用量;
In most engines, do not overbore more than .030", or localized heating of the water jacket may occur, not to mention a twisting cylinder bore under hard engine loads. 在大多数发动机;不要否决了超过.;030”;或局部加热水的夹克;更不用说一个扭载荷下的发动机气缸孔难。
How can we bear wearing the suits to negotiate in so hot a day! 在这么热的天穿着厚厚的西装去谈判,我们怎么受得了!
Push the glove box lock cylinder firmly into the lock cylinder bore while rotating the key and cylinder counterclockwise to the 6 o'clock position, where the lock cylinder retaining tumbler will snap back into place. 将手套箱锁柱压入锁柱孔，同时逆时针旋转钥匙和锁柱至六点钟位置，这样锁柱定位卡簧将弹回原处。
Push the glove box lock cylinder firmly into the lock cylinder bore while rotating the key and cylinder counterclockwise to the6 o' position, where the lock cylinder retaining tumbler will snap back into place. 将手套箱锁柱压入锁柱孔，同时逆时针旋转钥匙和锁柱至六点钟位置，这样锁柱定位卡簧将弹回原处。
A method was put forward,of which the actual law of bore wear and its corresponding muzzle velocity loss was obtained by simulating the law of bore wear,its corresponding muzzle velocity loss and weighting coefficient. 通过模拟的炮膛磨损规律及其对应的初速减退量和权系数,提出求得实测炮膛磨损规律对应的初速减退量的方法。
The stroke of cylinder bearing with compressing loading is controlled by buckling strength. 承受压缩负载的油缸的行程通过压曲强度来控制。
When ordinary honing process is applied to machine a cylinder bore, oilstone is often clogged, machining efficiency is low together with high noise and low machining surface finish. 缸筒内孔采用普通珩磨工艺时，油石易堵塞，加工效率低，噪声大，加工表面质量差。
Use of the bearing oil leak detector will determine whether or not bearing wear has been uneven. 使用漏油检测装置即可判定轴承磨损是否均匀。
Tears are secreted by an organ under the upper eyelid. 眼泪由上眼睑下面的器官分泌。
Ultra-high precision cylinder bearings with high-quality needle roller bearing or tapered roller bearing to ensure machine superb durability. 印刷滚筒轴承均采用进口高精度滚针轴承或圆锥滚子轴承,确保机器的稳定可靠及耐用性。