该词条未找到_海词词典

您要查找的是不是：

timber surface defect 木材表面缺陷
Segmentation Method of Timber Surface Defects Based on Gray Level-Gradient Co-occurrence Matrix 基于灰度-梯度共生矩阵的木材表面缺陷分割方法
A surface defect in paper. Alternative terms: blisters; foam marks. 中义纸张的表面缺陷，参考字：气泡痕迹。
timber surface defects 木材表面缺陷
Surface defect and macrostructure of high carbon steel billet were analyzed. 介绍了铸坯相关表面缺陷及低倍组织,提出了质量控制措施及方案。
Exterior measurement includes specification and size, surface defect, and sewing requirement. 外观质量包括规格尺寸及公差、表面疵点、缝制要求。
Zinc content in the alloy above 0. 05% consistently resulted in an unacceptable surface defect as galvanizing. 锌含量低于0．05%25时，型材一般不发生雪花状腐蚀。
Lacquer timber surface gives heavy blackening: The likelihood is knag going up Qi Qian was not sealed, classics sun is basked in, knag be heated, colophony from knag inside oozy and cause. 漆木料表面出沉暗斑：可能是木节在上漆前未封住，经太阳一晒，木节受热，树脂从木节内渗出而引起的。
Surface defect detection is important to ensure the utility,integrality,and security of the products. 产品表面缺损检测对保证产品的使用性能、完整性和安全性具有重要意义。
The article describes the problem of the toughened glass' surface defect and the method of prevention and solution. 针对钢化玻璃表面质量存在的变形点缺陷,采取相对应措施预防和解决。
Small and superficial occlusal surface defect ,proximal and labial surface defect uninvolved incisal angle . 2 .;合面缺损范围小而且表浅，前牙邻、唇面缺损未涉及切角者，不宜用嵌体修复。
Using flexible interpolator pad is an important way to suppress the part surface defect in stretch-farming process on multi-paint tool. 摘要采用柔性垫层是抑制和消除多点模拉形过程中零件表面缺陷的重要措施。
This paper analyzes the reason that caused the surface defect of billet produced by EAF Steelmaking plant of Nanjing Iron and Steel Co.Ltd. 分析了南(京)钢电炉厂小方坯表面质量问题及产生的原因,涉及结晶器振动参数、保护渣等。
Objective: To provide anatomic basis for repairing the knee joint surface defect with the pedicled patella translocation. 摘要目的：为带血管蒂髌骨移位修复股骨髁和胫骨髁关节面缺损提供解剖学基础。
Using flexible interpolator pad is an important way to suppress the part surface defect in stretch-forming process on multi-point tool. 采用柔性垫层是抑制和消除多点模拉形过程中零件表面缺陷的重要措施。
The results show that 82B wire rod brittle fracture is mainly caused by excessive inclusion,reticulate carbide,lower sorbite in the microstructure,and surface defect of wire rod. 结果表明,82B钢盘条脆断的主要原因是夹杂物级别超标、组织中出现网状碳化物、索氏体含量偏低以及盘条表面缺陷等。
The firm's tender for the supply of timber has been accepted. 那家商号的供应木材投标已被接受。
Surface defect in cold rolled galvanization plate in Handan Iron and Steel Limited Group has been introduced,meanwhile the solution process has been discussed. 介绍邯钢冷轧热镀锌线在生产中所遇到的一些表面缺陷,及对解决过程中所遇到的一些问题进行探讨。
The main shortages in MnSi surface and the reasons are analysed,the measures to improve MnSi surface quality and to reduce the loss by the surface defect are put forword. 分析了锰硅合金表面质量的主要缺陷及其产生的主要原因，提出了改善锰硅合金表面质量，减少因表面质量缺陷而造成损失的措施。
On the basis of the rigid viscoplastic FEM theory, a surface defect prediction method for the plastic forming process by FEM numerical simulation has been thoroughly studied. 摘要基于刚粘塑性有限元基本理论，本文深入地研讨了通过有限元数值模拟来预测塑性成形问题中一类表面缺陷生成的方法。