您要查找的是不是:
- suction side bearing cover 吸入口轴承压盖
- Foot valves are normally installed in an open tank or sump on the suction side of a pump. 通常底阀是安装在一个开口罐里,或泵的吸入一侧的液体坑里。
- The higher harmonics of the rotor BPF in the fore part of the suction side are more prominent than that in the other parts of the stator blade. 转子尾迹频率的高频分量对静子叶片吸力面前缘的影响比对其他位置的影响大。
- At the larger mass flow, the relative velocity at the middle channel was higher than that both of suction side and pressure side of the impeller at the inlet section. 流量大于设计流量时,在流道入口段中线附近区域流体的相对速度较大,压力面和吸力面附近流体的相对速度均较小;
- Excessive speed of rotation of the impeller is liable to cause the pressure on the suction side to fall so low that the liquid will vaporize, thus causing damage to the impeller. 随后这种动能便转换成静压能,于是又加大了泵的吸入管与排出管间本来就很大的压差。
- If the side bearing gap is too big, it will not restrain efficiently the roiling of car-body when roll restoring moment is not sufficient. 而过大的旁承间隙又使旁承在侧滚回复力矩不足时不能有效抑制车体的侧滚。
- Remove differential side bearings from differential case. 从差速箱拆卸差速器侧轴承。
- Besides, hot forgings of magnesium alloy for bearing cover of car are carried out to study the formability of magnesium alloy, and to find the best forging condition. 另外以镁合金棒材进行汽车轴承套盖零组件之热锻实验,以求得镁合金汽车轴承套盖零组件之最佳成形条件。
- A new measure to reduce the secondary flow loss of the stator cascade of steam turbine governing stage by means of the boundary, layer suction near the suction side of endwall is presented. 提出一种在调节级静叶栅叶片吸力面侧端壁处抽吸低能流体至轴封漏汽腔室,以降低静叶栅二次流损失的方法。
- Abstract: A new measure to reduce the secondary flow loss of the stator cascade of steam turbine governing stage by means of the boundary, layer suction near the suction side of endwall is presented. 摘 要: 提出一种在调节级静叶栅叶片吸力面侧端壁处抽吸低能流体至轴封漏汽腔室,以降低静叶栅二次流损失的方法。
- Equally effective in checking back flows from head pressure on the discharge or suction sides of pump. 无论是泵的排泄口的排出压力,还是泵的吸入口,其流体止回的效果都是相同的。
- Go in to anticipate to all take in to seal completely or establish watertightness,dampproof bore cover. 入料口均加以密封或设防水、防潮的孔盖。
- Trailing suction side caster dredger 边抛耙吸式挖泥船
- BOLTS AND NUTS FOR MAIN BEARING COVER 主轴盖螺栓螺母
- Stamping Craft and Mold Design Bearing Cover 轴承盖冲压工艺及模具设计
- The problems existing in reform of the upper side bearings assembly on present freight cars and the causes are analyzed. 分析了既有货车提速改造上旁承组装存在的问题及原因,并提出了相应的解决措施。
- conveyer end bearing cover bushing 输送机端承盖衬套
- Bogie side bearing sliding block 下旁承滑块
- Some pumps and all vacuum cleaners work by suction. 有些泵和所有真空吸尘器都是借吸力工作的。
- Then according to the bearing behavior of arcade tunnel,the internal force of one side bearing and both sides bearing have been calculated and analyzed by using the method of loading-structure. 接着根据连拱隧道的承载特点,按荷载结构法分析计算了单侧承载及整体承载条件下的隧道内力,据此提出了一种简化为单拱的计算方法。