您要查找的是不是：
- A small block of metal or wood with a central, threaded hole that is designed to fit around and secure a bolt or screw. 螺母，螺帽中部有螺纹用于与螺栓或螺钉相配合的小块金属或木头
- At the end of main screw, a screw hole with inverse thread is drilled and a small screw is screwed in and has antislip veins on the inner side of its died nut. 本发明技术构造在主螺杆外端头打一反丝螺孔，配以小螺杆，小螺杆死帽内侧有防滑纹，主螺帽外侧有防滑纹。
- The traditional design concept of bolt assemblage is broken,and the screw the threaded hole,the gasket,the boss(or the dimpling)are regarded as a whole. 打破传统螺钉联接设计思想,把螺钉、螺纹孔、垫片、凸台(或者沉头孔)看成一个整体,进行整体设计。
- Insert special bolt into the preset hole of C form parts ,where the bolt will be fixed into the threaded hole of wedge ,then screw the bolt on with a socket spanner until the first nut drops . 将专用螺栓插入C形无件预留孔与楔块的螺纹孔相连，用套筒扳手拧紧螺栓直到第一个螺帽自行断落。
- All lead wires are 18 AWG, 18 inches long and exit the actuator housing through a single threaded hole designed for 1/2-inch conduit fittings. 所有引线都是18AWG，18英寸长并且穿过1/2英寸导线管，从设计的单孔中引出执行机构外壳外。
- Technique properties: Taiwan groove broacher, international level specs, reasonable distribution of screw hole, suitable for wood and iron furniture. 产品工艺特点：主要采用台湾拉槽机，产品规格与国际接轨，装配的螺丝孔分布合理，适合各类木器，铁器等家具。
- If a threaded hole in the suspension cradle needs to be repaired, only use the type of thread insert and installation procedure specified for this application. 如果悬吊架有螺纹孔需要修复，仅限使用专用的螺纹套座以及特别安装程序。
- The design of reamer, which is made to machining the basic hole of tapered thread hole on the seamless steel resolvable ethine gas-jar, is introduced. 介绍了一种加工钢质无缝溶解乙炔气瓶锥螺纹底孔的铰刀设计方法,对铰刀的主要参数和特点做了简要分析。
- Only one wrench is able to install and dismount, due to fixed screw holes. 有固定螺丝孔，装卸只要一支扳手，更方便。
- The carriages have threaded holes for mounting on adjacent constructions. 车厢有螺纹孔用于安装在邻近的建设。
- Loose screws on the doors and windows, as long as the original screw hole into a match stick or toothpick and cement, and then screw into the screw on the list. 门窗上的螺钉松了，只要在原钉孔中塞进一根火柴棒或牙签并粘牢，然后再将螺钉拧进去就行了。
- All the bolts and screw holes of flanges must be supplied with graphit and moly bdenum disulphide to prevent. 由于吹灰器所处环境恶劣，所有法兰的螺栓、螺母的螺纹表面应涂抹石墨油脂或二硫化钼油脂加以保护。
- Use an Awl or nail to location and line up corner drilled holes with the corner screw holes in vent frame . 使用一锥或钉的位置和排队角落钻孔与角螺丝孔在发泄框架。
- Threaded holes in the housing shoulders also enable the use of screws to push the bearing from its seating (fig 33). 轴承座挡肩上开螺纹孔,可以使用螺钉将轴承推离支承面(图33)。
- screw hole of subperiosteal implant 骨膜下植入体螺钉孔
- The threaded holes in the front suspension cradle, if damaged, can repaired by installing a Heli-Coil® thread insert. 前悬吊架的螺纹孔如有受损，可装上Heli-Coil®螺纹套座加以修理。
- His strength in a crisis is an ace in the hole. 临危不惧是他的看家本领。
- Recommended dimensions for the appropriate grooves, ducts and threaded holes to connect the oil supply can be found in table 6 and table 7. 对于连接供油的合适注油槽、注油孔与螺纹孔的推荐尺寸可以在表6与表7中找到。
- Figure 7-43 GAP (graft augmentation prosthesis) acetabular cup has titanium ring with inferior hook and two superiorly placed plates with additional dome screw holes. 图7-43GAP（植骨加强假体）髋臼杯。臼杯有钛加强网，下方有钩，上方有两根板条，臼顶另有螺丝孔。
- To ease lifting, large bearings can be provided on request with threaded holes in the ring side faces to accommodate eye bolts. 为了方便起吊,特大型轴承可按要求在套圈侧面加上螺孔,以便固定吊环螺栓。
