该词条未找到_海词词典

您要查找的是不是：

recoil piston rod lug 驻退杆固定突座
recoil piston rod 驻退杆,驻退活塞杆
Worn crankcase piston rod seals O-rings on. 曲轴箱柱塞连杆O型圈磨损或柱塞衬套磨损。
Worn crankcase piston rod seals. 曲轴箱连杆密封件损坏。
Replace crankcase piston rod seals. Replace O-rings. 更换新的曲轴箱柱塞连杆O型圈。
When assembling, leave the mark on body of piston rod frontward. 装配时，杆身上的记号要朝前。
Th e piston rod should befitted with the crosshead arenow going tryit. 活塞杆应与十字头孔配合。
A beam that connects the piston rod to the connecting rod of a reciprocating engine. 十字头连接活塞杆和往复式发动机连杆的横杆
As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted. 当活塞下行时，棘轮连接活塞杆和发动机轴，因此将功率输送出去。
THE SEALING BETWEEN THE CRANKCASE AND SCAVENGING AIR BOXES IS ACHIEVED BY MEANS OF PISTON ROD STUFFING BOXES. 曲柄箱与扫气箱之间的密封是通过活塞杆填料函实现的。
A hydraulic lock is installed on the vertical leg cylinder to avoid extending of the leg piston rod in operation. 在支腿垂直油缸上装有液压锁,能可靠地防止行驶时支腿活塞杆伸出。
External diameter E and piston rod diameter D will not comply with the above standard due to different applications. 根据用途，缸体外径E，活塞杆直径d有时与上述尺寸不同。
Gas piston rod and receiver. Note the recess on the bottom of the receiver, it is for the bolt locking. 导杆及枪匣，注意枪匣内下方的凹槽，供枪机闭锁用。
An oscillating lever connected to an engine piston rod and used to transmit power to the crankshaft. 传动杆可摆动的杠杆，与引擎之活塞相连，用以向机轴传送能量
In all designs, the valve stem normally serves as a piston rod with disc fastened directly to them. 在所有结构中，阀杆通常作为活塞杆，阀瓣直接固定在阀杆上。
The AFO cylinder features include a stainless steel tube and roller burnished piston rod. 气缸的踝足矫形器功能还包括一个不锈钢管，辊磨光活塞杆。
The piston rod of family sedan's rear snubber fractured duringearlier stage of rotary bending fatigue test. 家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
Hard-chromed piston rod with micro-grooves, increasing the rigidity and reducing friction, keep better lubrication action. 活塞杆微裂纹镀硬铬,增因硬度减少磨擦,保持油膜润滑效果值。
Abstract： The piston rod of family sedan’s rear snubber fractured during earlier stage of rotary bending fatigue test. 摘要：家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
This paper introduces the problems of disc type deburrer installation debugging and made a depth piston rod steering structure analysis. 针对圆盘式去毛刺机在安装调试中出现的问题,分析了其活塞杆导向结构,提出了解决方案,最终得到满意的结果。