您要查找的是不是：
- Serofluid will boil below, together with other condiments, pulp mold surface. 将浆水烧开下面，再配以其它佐料，即成浆水面。
- The sodium silicate makes the cork stick to the mold surface and also helps to withstand the charring action of the molten lead alloy. 硅酸钠能使软木粉粘结在模具表面，而且还有助于软木粉耐受熔融铅合金的碳化作用。
- Too much water reduces the adhesion and too little piles the material up too thick on the mold surface. 水太多会减少粘附力，加水太少则会使脱模剂在模具表面堆积太厚。
- In general, mold surface temperature lower than 82 C (180 F) may produce a hazy surface or a surface with flow lines, pits and other include defects. 大体上，形成表面的温度比82个C(180F)低可能用流程线生产一个朦胧的表面或者一个表面,坑和其他包括缺点。
- Leading in adoption ASSAB forged mold surface complex treatment ABP method, elevate the service life of the forged mold successfully. 率先采用ASSAB锻模表面复合处理ABP工法，成功提升锻造模具寿命。
- Suitable for work piece with the larger variation of grinding angle and grinding special shape of for mold surface for mold industry or general stone masonry handicrafts. 适用于研磨角度变化较大工件及模具业研磨较特殊形状之模具表面或一般石雕工艺品。
- Surface grain refinement of turbine blades in Ni based superalloy K18 were studied by comparison of experimental results in different alloys and mold surface materials. 选用K18合金和纯金属镍及不同的面层细化料,通过实验对比研究了镍基高温合金叶片表面晶粒细化机理。
- Surface treatments on continuous casting mold (CCM) will greatly increase its service life and electroplating is the leading surface technology in the field of mold surface treatment. 摘要对结晶器进行表面处理可以欠大提高其使用寿命，电镀技术是结晶器表面处理领域的主要表面技术。
- Wall thickness greater than 3mm (1/8 in.) may use a cooler (65 C/150 F) mold surface temperature and wall thickness over 6mm (1/4 in.) may use a cold mold surface down to 25 C (80 F). 墙壁厚度比3毫米大(1/8在.;)可能使用冷却器(65个C/150F)模子表面的温度和超过6毫米的墙壁厚度(1/4在
- May require mold temperatures as high as 120 C (250 F) to reproduce mold surface or to assure minimal molded in stress. 可能需要模子温度高达120个C(250F)再生模子表面而且保证最小的在压迫力形成。
- Based on the principle of discretization to manufacture rough mold surfaces,combined with the results of CAE analysis, a new stagger layout of pin-lifts is put forward. 根据离散化方法制造模具型面毛坯的原理,结合CAE分析的结果,提出了一种新的顶杆错位布置方法。
- D.H.Kim, M.H.Kan and Y.H.Chun, ”Wonder Injection Molding with Momentary Mold Surface Heating Process(MmSH Process)”, SPE ANTEC Tech.Paper, pp.3841-3844. (2000). 李育芸;“感应加热应用于模具表面快速加热之研究”;私立中原大学机械工程学研究所硕士论文(2002).
- He is cast in his father's mold. 他长得和他父亲一模一样。
- In this paper the on-line real-time detecting system of molder surface temperature of continuous casting is designed. 设计了连铸铸坯表面温度在线实时测量系统。
- The gas bubbled to the surface of the water. 气体变成气泡升上水面。
- The surface of the liquid gradually crusted over. 液体表面渐渐地结了一层皮。
- Many wild flowers grow in the forest mold. 森林里的松软沃土上长著许多野花。
- Women of her mold are easy to see through. 她那种性格的女人是很容易看穿的。
- A breeze ruffled the surface of the lake. 一阵微风吹皱了湖面。
- We need more people of his mold. 我们需要更多他那种类型的人。
