该词条未找到_海词词典

您要查找的是不是：

drive pinion and shaft 主动小齿轮及轴
Refer to Drive Pinion Bearing Pre-Load Adjustment. 参阅驱动小齿轮轴承预荷调整。
Worn teeth on ring gear or drive pinion gear. 环形齿轮或驱动小齿轮上齿磨损。
End play in drive pinion bearings. 驱动小齿轮轴承的端隙。
The drive pinion is beveled at 45 degrees and engages the ring gear, which is also beveled at 45 degrees, causing the ring gear to revolve at 90 degrees to the drive shaft. 该驱动器齿轮是斜45度和参与的齿圈，这也是斜角在45摄氏度，造成齿圈旋转90度的传动轴。
Tube and shaft cut and machined by CNC machines and Robots. 钢管和轴承由CNC机器和机器人来切割和处理。
differential spur drive pinion cross shaft 差速[减速]器主动齿轮横轴
A new version of face gear drive geometry was proposed as envelopes of two parabolic racks of the pinion and shaper in the profile. 提出了一种沿齿廓方向抛物线修形的面齿轮齿面结构，对传统斜齿面齿轮和修形的斜齿面齿轮副的啮合进行了比较。
The ring gear is attached to the differential case so that the ease rotates with the ring gear when the latter is driven by the drive pinion. 冠状齿轮与差速器壳相连,这样当冠状齿轮由传动齿轮驱动转动时,差速器壳也转动。
An over-running clutch on the drive pinion prevents the starter from being driven by the engine once it starts. 在驱动小齿轮上的一个超转离合器可避免启动马达被引擎带动，一旦引擎启动了。
The wings of the ostrich flap joyously: Are they the pinion and plumage of lovingkindness? 13鸵鸟的翅膀欢然扇展，岂是显慈爱的翎毛和羽毛么?
The influence of the force location and helix angle on the bend stresses of pinion and face-gear is discussed. 讨论了外力作用位置沿齿长方向变化与螺旋角变化时圆柱齿轮和面齿轮弯曲应力的变化规律。
Remove the headlamp switch knob and shaft from the headlamp switcSee Headlamp Switch in this group for the procedures. 请将头灯开关按钮和轴从头灯开关中拆下。请参考本单元的头灯开关的程序。
Among ways to provide rotational control of the rims within the frames are a pinion and gear system or a chain and sprocket system. 在方法之中在框里面提供边缘的旋转控制是小齿轮和传动机构系统或链条和链轮系统。
While holding the release button depressed, pull the knob and shaft out of the headlamp switch. 保持钮的按住状态，将按钮和轴拉出开关。
Bill wave his hand to us and then drive away. 比尔向我们挥手告别后开车走了。
Two types of drill jigs locating plate and shaft parts with cylindrical locators are introduced. 分别介绍了依据圆柱体母线对板类及轴销类零件进行定位的两种钻模。
Abstract The key technology of hollow assembled camshaft is connection between camlobes and shaft. 摘要中空装配式凸轮轴的技术关键为凸轮与轴体的连接。
Hold the yoke with Wrench 67Remove the pinion shaft nut and washer. 用扳手6719握住轴轭。拆下小齿轮轴螺帽和垫圈。