该词条未找到_海词词典

您要查找的是不是：

The Analysis of Design Bending Moment in In-place Concrete Hollowed Flat Floor 现浇钢筋混凝土空心无梁楼盖设计弯矩分析
designed bending moment 设计弯矩
A practical method of calculation for designing bending moment of base plate of reinforced concrete independent foundation under column 柱下钢筋混凝土独立基础底板设计弯矩的实用计算方法
The actual stress is not proportional to the bending moment. 实际上应力与弯矩不成正比。
But the bending moment at the central hinge must vanish. 但在中间铰处，弯矩必定为零。
In structural design,intensity stiffenss and stability need to be calculated,thereinto, calculation of absolute maximum bending moment and position is the most important. 在结构设计中,需要对梁的强度、刚度、稳定性等方面进行计算,其中绝对最大弯矩及位置的计算极为重要的。
Next, carries on the structure endogenic force combination, definite structure control section bending moment, shearing force and axle strength design value. 其次，进行结构内力组合，确定结构控制截面的弯矩、剪力和轴力设计值。
The induced bending moment may lead to destructibility of the pipeline. 弯矩的产生可能导致管线的破坏。
Shear force is implicit in the development of bending moments. 杆中的剪力在弯矩的推导中是不明显的。
This increases both the rigid body rotation of the vehicle and the bending moment. 这既增加了飞行器的刚体转动，也增加了弯矩。
In the FEM simulation of the loading identification process, the bending moment maintains a constant amplitude, hut its direction is alterable. 在有限元仿真计算中，弯矩载荷的大小保持不变，但方向可调。
The unique phenomena at any cross section of EULER compressive bar under the zero bending moment is analyzed. 从理论上分析了欧拉压杆任意截面上弯矩为零的状态下所出现的奇异现象。
In this paper a function calculation method of preloaded bending moment distribution for leaves of spring is des... 本文介绍了一种用于板簧簧片预加弯矩分配计算的函数计算法,并给出了计算实例。
The needed pipe bending moment、wall thickness reduction and ovality of section are known by simulating. 通过模拟,计算管子弯曲变形所需的弯矩,计算管子弯曲部分外壁减薄率和椭圆度。
Moreover, the influence of initial crookedness would be reduced as slenderness ratio and bending moment are increased. 初弯曲对杆件的影响随长细比和弯矩的增大而减小；
The bending moment of common prestressed concrete pipe piles is relatively low under the horizontal earthquake action. 摘要普通预应力混凝土管桩在水平地震作用下抗弯能力较差；
The connection of CHS T-joints with fold chord subjected to in-plane bending moment can be simplified as rigid joint. 在平面内弯矩作用下，弦杆为折杆的T型圆钢管节点计算可以简化为刚接节点模型。
The calculation of ledger maximum bending moment and deformation the even load of scaffold board and live loads above the ledger. 按照大横杆上面的脚手板和活荷载作为均布荷载计算大横杆的最大弯矩和变形。
The Settlement both vertically and horizontally under lateral loads and bending moment must not exceed predetermined and acceptable values. 垂直和水平向荷载作用下的沉降和弯(曲)矩不能超过预先确定数值或工程采用的限定数值。
The bending moment can be related to the formation drillability, BHA configuration and drill bit size, and is proportional to the applied WOB. 钻头弯矩与交错层的可钻性、下部钻具的结构和钻头的几何尺寸有关,并且与所加的钻压成正比。