您要查找的是不是：
- clamp bolt hole 夹紧螺栓孔
- Bolt hole fitting plastic core industrial caster. 孔顶塑芯工业脚轮。
- Lug body available with ISO flange dimensions and metric bolt hole threads. 凸耳式阀体符合ISO法兰尺寸和公制螺栓孔螺纹。
- Limited distance deviation of the optional bolt hole on flange shall be 2mm. 法兰上非强制螺栓孔的有限距离偏差应该为2毫米。
- The paper describes a kind of mobile drill clamp that fits different-diametical bolt holes and hole numbers.And details the functions and application ways of each parts and their conditions in site. 介绍一款能适应多种螺栓孔(或光孔)所在圆的直径(简称孔位直径)和孔数的可转位钻孔夹具结构,并详细说明了各个部件的功用和使用方法以及现场使用情况。
- The bolt holes are in the unit base. 螺栓孔在单元的基部。
- Lug body available with ISO flange dimensions and metric bolt hole threads. For dead-end service use lug style (rated 200 PSI for this service). 凸耳阀体也可配置ISO法兰尺寸和公制螺栓孔螺纹。用于终端位置可采用凸耳结构（此时额定压力为200PSI）。
- Keywords bolted sphere node of grid virtual sphere center datum dividing and clamping bolted hole; 网架节点球;虚拟球心基准;分度夹紧;螺纹孔;
- There is standard bolt hole connecting with the valve or bracket.The output axis in the middle is a standard internal octagon. 壳体上有标准的螺孔与阀门或支架相连。中间输出轴为一个标准的内八角。
- Looking for a bolt hole for you and your loved one this Valentine's Day? This selection of romantic retreats should inspire you. 充满充满波西米亚风情的广场酒店，一定会让你流连忘返。不过，要注意你的口袋哦，每天145英镑的花费，应该不算少。
- Position flywheel and O-ring on crankshaft and align bolt holes. 安装飞轮和O形环在曲轴上并对齐螺栓孔。
- Anchor/support bolt holes are located in base of body. 固定器/支架螺栓孔位于阀门的基座。
- Centerline of the slot at base of distributor is aligned to centerline of distributor holddown bolt hole on enginIn this position, the holddown bolt should easily pass through slot and into engine. 在分电盘基座上槽的中心线应与引擎上分电盘垂下螺栓孔的中心线对准。在这个位置，垂下螺栓应容易地通过槽进入引擎。
- The dimension tolerance of bolt holes shall meet the following requirements. 螺栓孔的尺寸公差应满足以下要求
- Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block. 在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
- The wood is held in position by a clamp. 木头用钳夹固定住了。
- Block front fork of valve disassemble tool onto cylinder head sub bolt hole, pressing this tool downwards by a force application bar until the two pieces of lock are falling down, see chart 3b. 在拆卸气门锁片时，用气门拆卸工具的前叉卡在缸盖付螺栓上，然后用加力杆向下压动气门拆卸工具，直到两锁片脱出为止，如图3b。
- His strength in a crisis is an ace in the hole. 临危不惧是他的看家本领。
- There are three lifting holes and one lifting bolt hole on thefront and rear of the machine bed for plugging lifting hooks or bars. 床身前后共有三个起重孔和一个起重螺栓孔，用以插入起重工具。
- Note: 1.Size-Nominal diameter of the valve; D1-Diameter of the flange bolt hole center circle; D-Diameter of the flange bolt holes. 注:1.;规格尺寸为阀门通径尺寸;D1为阀门法兰孔中心分布圆尺寸;D为法兰孔直径。
