您要查找的是不是:
- Airborne Angular Position Sensor 机载角位传感器
- Non-contact Angular Position Sensor Based on Transceiver Concept 基于收发器技术的非接触式角度传感器的研制
- Study of Intelligent Differential Capacitive Angular Position Sensor 智能化差动电容角位移传感器的研究
- angular position sensor 角位置传感器
- REPAIR THE OPEN CRANK POSITION SENSOR SIGNAL CIRCUIT. 维修断开的曲柄位置感知器信号电路。
- One solution is to add a rotor position sensor to the synchromotor. 解决这一问题普遍的做法是加装电机转子位置传感器。
- There only use one position sensor to achieve the dual coils commutator. 该换向电路与双位置传感器一起还能够实现双触发双余度换向。
- angular position type density sensor 角度位置式密度传感器
- The paper describes the error analysis for this accuracy angular position transducer and the method for eliminating the error. 文中对这种高精度角位置传感器产生误差原因进行了分析,并给出了有效消除误差的方法。
- The photoelectric encoder is used for measuring the angular position of rotating ballscrew.Semi closed loop compensation control is realized and system accuracy is improved. 应用光电编码器作为滚珠丝杠转角位置检测元件实现了半闭环补偿控制,提高了系统的精度。
- Position sensor to throttle body while guiding rubber fitting over throttle body vacuum nipple. 在节气阀体真空管接头上面操纵橡胶管件时,定位感知器至节气阀体。
- The state observer observes the precise load torque, rotor position and speed with only a low accuracy position sensor. 状态观测器可以利用较低精度的位置传感器来准确观测负载转矩、转子位置和转速。
- There are position sensor windings in addition to armature windings in the motor. 这种电机内部除了电枢绕组以外,还带有位置传感线圈。
- Robot's soft griping function relies on the fine-performance force sensor, position sensor and slip sensor. 摘要机械手软抓取功能的实现,关键在于有性能优良的滑觉传感器。
- Disengage in unprecedented2 to4 msecs of an overload signal, compared to conventional couplings that take a full second to disengage. Ours automatically re-engage at the precise angular position. 接到过载信号后,2-4毫秒断开。并且以精确的角度自动重新连接。这个时间是无法比拟的。常规联轴器需要1秒时间。
- Robot s soft griping function relies on the fine-performance force sensor, position sensor and slip sensor. 机械手软抓取功能的实现,关键在于有性能优良的滑觉传感器。
- Model of self-generation of angular positioning precision during mutual lapping machining process for end-tooth indexing table was built. 着重阐述了端齿盘对研加工系统的误差自去除原理及其分度精度自组织机制。
- Supplies the required 5 volt power source to the crankshaft position sensor, camshaft position sensor, MAP sensor and throttle position sensor. 向曲轴位置感应器、凸轮轴位置感应器、MAP感应器以及节气阀位置感应器提供所需的5伏电压。
- The first cylinder would be measured by the trigger cam of crankshaft position sensor and sensor that are installed on the cramshaft axis. 第一缸的检测通过安装在凸轮轴轴线上的凸轮轴位置传感器触发轮及传感器进行测量。
- Furthermore, this dissertation proposes a novel commutation control for the FSTP BLDC motor drive without position sensor. 此无感测控制是侦测两相浮动电压讯号的交越点,以求出转子所需要的换相时机。