您要查找的是不是：
- Weak parting Line 有分离线
- Parting line at the acceptable surface. 合模分布在合理可接受的表面。
- Parting line cleared and released properly? 分模线是否正确?
- Parting line locks are required on all molds. 琐模块所有的模具都需要。
- The parting line tolerance for gib installation is +.000/-.002. 安装导板的分模线公差为+.;000/-
- The dynamic characteristic analysis of ship lifter has always been a weak part of the lifter field. 船用升降机动力学性能分析一直以来都是升降机领域的一个薄弱环节。
- The paper introduced two kinds of separator in tank, presented a finite element analysis for their forced structure, point out the weak part. 摘要介绍了储罐的两种隔板形式，对其受力结构分别进行了有限元分析，指出了强度薄弱部位。
- Assesses and analyses the reliability of an actual heat-supply network,finds the weak part,and thus improves the reliability. 对一实际热网进行了可靠性评估和分析,找出了热网的薄弱环节,提高了其可靠性。
- Teacher's classroom management behavior is a basic fator that affects teaching qualities and efficiency, and is a comparatively weak part in the present studies of teaching. 教师的课堂管理行为是影响课堂教学质量与效率的基本要素,也是当前教学研究中的一个相对薄弱的环节。
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗?
- And yet today that is the weakest part of software technology. 而且仍然是软件技术的最弱部份的今天。
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因为手遮光，请将分界线在图中标出来，并告诉确切尺寸。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精确配合或有擦位的地方,模具一定要有直身锁。
- Further, practicing the speech out loud will help the speaker identify the strong and weak parts of the speech. 再者，大家演练讲稿也可以帮助演讲人知道演讲内容的强弱之处。
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考虑到动模维护需要,封胶面应有1”左右的偏移增量。
- The spirit is willing but the flesh is weak. 心有余而力不足。
- We can render their assistance are only a weak part, we hoped has more people to help them, enables them to accept a better education, because their each people all will be star of the tomorrow! 我们所能给予他们的帮助只是微弱的一部分，我们希望有更多的人去帮助他们，使他们能接受到更好的教育，因为他们每一个人都是明日之星！
- The optimization parting direction was determined after all undercut features were distinguished, and the parting line and parting surface were confirmed accordingly. 通过侧凹特征的判别确定模具的优化脱模方向，并确定模具的分型线和分型面。
- Interfaces are the weakest parts in a concrete structure. 摘要界面是混凝土结构中最为薄弱的环节。
- The selection of parting line,the determination of round sprue runner diameter,the design of round sprue runner shape and pouring gate form were presented. 介绍了模具分型面的位置选择、圆形流道直径的确定、圆形流道形状的设计、浇口形式等。
